Manual de instruções Boss Audio Systems Chaos Exxstreme CX2500D

Boss Audio Systems Chaos Exxstreme CX2500D
(1)
  • Número de páginas: 11
  • Tipo de arquivo: PDF

Troubleshooting

CX2500D • CX3500D Amplifier User’s Manual - page 10

Specifications

CX2500D • CX3500D Amplifier User’s Manual - page 11
CX2500D • CX3500D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

CX2500D • CX3500D Amplifier User’s Manual - page 4
CX2500D • CX3500D Amplifier User’s Manual - page 3
CX2500D • CX3500D Amplifier User’s Manual - page 8
CX2500D • CX3500D Amplifier User’s Manual - page 5
CX2500D • CX3500D Amplifier User’s Manual - page 7
CX2500D • CX3500D Amplifier User’s Manual - page 9
CX2500D • CX3500D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes

If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous pages. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
Low-level (RCA) input wiring is preferred for best audio performance. Always use
a high-quality RCA cable for best audio performance.
Protection LED
comes on when
amplifier is
powered up.
Check for short circuits on speaker leads.
Turn down the volume control on the head unit to prevent overdriving.
Remove speaker leads, and reset the amplifier. If the Protection LED still
comes on, then the amplifier is faulty and needs servicing.
High hiss in the
speakers.
Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then
plug in the component driving the amplifier and unplug its inputs. If the
hiss disappears at this point, go on until the faulty/noisy component is
found.
It is best to set the amplifier's input level control as low as possible. The
best subjective signal-to-noise ratio is achieved in this manner. Try to set
the head unit as high as possible (without distortion) and the amp input
level as low as possible.
Squealing noise
from speakers.
Check for improperly grounded RCA interconnects.
Distorted sound.
Check that the Input Level Control is set to match the signal level of the
head unit. Always try to set the Input Level as low as possible.
Check that all crossover frequencies are properly set.
Check for short circuits on the speaker leads.
Amplifier gets
very hot.
Check that the minimum speaker impedance for the amp model is correct.
Check that there is good air circulation around the amp. In some
applications, it may be necessary to add and external cooling fan.
Engine noise
(static type)
This is usually caused by poor quality RCA cables,which can pick up
radiated noise. Use only the best quality cables, and route them away
from power cables.
Engine noise
(alternator
whine)
Check that speaker leads are not shorted to the vehicle chassis.
Check that the RCA grounds are not shorted to the vehicle chassis.
Check that the head unit is properly grounded.
The fuse ratings for these amps is
40A (using two 20A fuses) for the
CX2500D and 90A (using three 30A
fuses) for the CX3500D. Although
sufficient for normal working
conditions, overloading the amp may
result in blown fuses. Please try to
avoid overloading the amp in this
manner.

Your CHAOS EXXTREME Class

D amplifier is designed to run
with a minimum load of 1 Ohm.

Operating the CX2500D or

CX3500D with a speaker im-
pedance load below 1 Ohm
may result in poor sound qual-
ity and damage to the amplifier
circuitry. Such damage is not
covered under the warranty
for this product.
Bridging Two CX2500D or Two CX3500D Amplifiers
MASTER
AMPLIFIER
Front panel
SLAVE
AMPLIFIER
Front Panel

Power Connections

Without Stiffening Capacitor
With Stiffening
Capacitor
Bridging Two CX2500D or Two CX3500D Amplifiers
SLAVE
AMPLIFIER
Rear Panel
INPUT CONNECTIONS
(SEE NEXT PAGE FOR POWER, SPEAKER AND DATALINK CONNECTIONS)
POWER AND SPEAKER CONNECTIONS
(SEE PREVIOUS PAGE FOR INPUT CONNECTIONS)
If there is smoke or any peculiar odor
present during use or if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the amplifier to your local
dealer or service center as soon as
possible .
3. Mark the location for the mounting
hole screws by positioning the amplifier
where you wish to install it. Use a scribe
or mounting screw, inserted through
each of the amp's mounting holes, to
mark the mounting surface. If the
mounting surface is carpeted, measure
the hole centers and mark with a felt
tip pen.
4. Drill pilot holes in the mounting
surface for the mounting screws. Place
the amplifier in position, and attach
the amplifier to the mounting surface
securely using screws.
4. Check that the fuse holder is empty.
Then connect the fuse holder to the
"BATT+" connection on the amplifier.
5. If multiple amplifiers are being used
in your system, either:
• Run a separate pair of cables from
the battery and a chassis ground point
to each amplifier. Each (+) cable must
have its own inline fuse.
-or-
• Run a #0 cable from the fuse holder
at the battery to a distribution block
at or near the amplifier's location. Then
run separate cables from the amplifier
to this distribution block and to
independent chassis ground points.
6. Connect all line inputs and outputs
(if used) using high-quality cables.
Connect all speakers, following the
diagrams in this manual. Be sure to
observe proper polarity to avoid audio
phase problems.
7. Insert fuse(s) into the battery fuse
holder(s).
8. Recheck all connections before
powering up the amplifier.
9. Set all level controls to minimum
position, and set all crossover
controls/switches to the desired
frequency points.
10. Power up the head unit and the
amplifier. Then set the volume control
on the head unit to about 3/4 volume,
and adjust the amplifier’s input level
control(s) to just below the level of
distortion.
11. Further fine tuning of the various
controls may be necessary to obtain
best results.

Speaker Connections

MASTER
AMPLIFIER
Rear panel

2 Introduction

2 Features

3 What is included?

3 General precautions

3 Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5 Important system considerations

5 Tips for a safe system

6 Low level input wiring

6 Speaker wiring

7 Power connections

Normal and with Stiffening Capacitor

8 Bridging two CHAOS EXXTREME

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your
purchase of a
CHAOS EXXTREME Class D
Amplifier.
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
Thank you for making
your choice for car audio
entertainment!
All specifications subject to
change without notice.
RMS POWER
into 4 Ohms
RMS POWER
into 2 Ohms
MAX POWER
into 2 Ohms
MAX POWER
into 1 Ohm
Min. speaker
impedance
Input
impedance
Input
sensitivity
Frequency response
Signal-to-noise ratio
Crossover/filter range
low pass
subsonic
Bass Boost
Phase Shift
Fuse rating
Dimensions:
(11
-7/8
" x 2
-5/8
" x ...)
750W x 1
1200W x 1
1800W x 1
2500W x 1
1 Ohm Mono
10k Ohm
Selectable 100mV-2V or 2V-8V
40Hz-150Hz
100dB
50Hz-150Hz
15Hz-40Hz
Variable 0 -+18dB
Selectable 0/180º
35A x 2
12-3/4"
MODEL
page

CX3500D

CX2500D

CLASS D MonoBlock
Car Audio Amplifiers
CLASS D
MonoBlock Car Audio
Amplifier
1200W x 1
1700W x 1
2200W x 1
3500W x 1
1 Ohm Mono
10k Ohm
Selectable 100mV-2V or 2V-8V
50Hz-150Hz
100dB
50Hz-150Hz
15Hz-40Hz
Variable 0 -+18dB
Selectable 0/180º
35A x 3
14-7/8"
CLASS D
MonoBlock Car Audio
Amplifier
SYMPTOM POSSIBLE REMEDY
CX2500D • CX3500D Amplifier User’s Manual - page 1
BRIDGED MODE
SWITCH IN MASTER
POSITION
BRIDGED MODE
SWITCH IN SLAVE
POSITION
To Audio Outputs of head
unit or Subwoofer outputs
of a signal processor
To Audio Inputs of
satellite amplifier
(if present)
To Audio Outputs of
head unit or
Subwoofer outputs
of a signal processor
Chassis
ground
point
Boss Audio Systems Chaos Exxstreme CX2500D

Precisa de ajuda?

Número de perguntas: 0

Você tem alguma dúvida sobre o Boss Audio Systems Chaos Exxstreme CX2500D ou precisa de ajuda? Faça sua pergunta aqui. Forneça uma descrição clara e abrangente do problema e sua pergunta. Quanto mais detalhes você fornecer para seu problema e pergunta, mais fácil será para outros proprietários de Boss Audio Systems Chaos Exxstreme CX2500D responderem adequadamente à sua pergunta.

Veja o manual do Boss Audio Systems Chaos Exxstreme CX2500D aqui, de graça. Este manual está na categoria Receptores e foi avaliado por 1 pessoas com uma média de 9.2. Este manual está disponível nos seguintes idiomas: Inglês. Você tem alguma dúvida sobre o Boss Audio Systems Chaos Exxstreme CX2500D ou precisa de ajuda? Faça a sua pergunta aqui

Boss Audio Systems Chaos Exxstreme CX2500D especificações

A comodidade na palma da sua mão, com um telecomando que torna o controlo do seu monitor mais fácil do que nunca.
Geral
Marca Boss Audio Systems
Modelo Chaos Exxstreme CX2500D
Produto Receptor
Língua Inglês
Tipo de arquivo PDF
Áudio
Canais de saída de áudio 1.0 canais
Potência do pico por canal 2500 W
Classe de amplificador D
Total Harmonic Distortion (THD) 0.01
Rácio Signal-to-Noise (SNR) 100 dB
Extensão da frequência 15 - 150 Hz
Mudança de fase 0 - 180 °
Bass boost 0 - 18 dB
Potência de saída RMS por canal (2 Ohm) 1200 W
Potência de saída RMS por canal (4 Ohm) 750 W
Potência dinâmica por canal (2 Ohm) 1800 W
Impedância de entrada 10000 Ω
Crossover incorporado Sim
Frequências crossover 50 Hz
Filtro subsónico Sim
Frequência de filtro subsónico 15 - 40 Hz
Conectividade
Tipo de conetividade de alto-falantes Terminais de fixação
Quantidade de portas USB 2.0 0
Entrada áudio (L,R) 1
Áudio (L,R) saída 2
Entrada XLR Não
Porta DC-in Sim
Entrada digital de áudio coaxial 0
Saída digital de áudio ótico 0
Entrada coaxial de áudio digital 0
Saída digital de áudio coaxial 0
Entradas de linha (RCA) 2
Ligação ao PC Não
Detalhes técnicos
Cor do produto Alumínio
Propósito Carro
Tecnologia de conetividade Com fios
Controlo do volume Rotativo
Ajuste de ganho Digital
Controlo do nível de graves Sim
Controlo do nível de agudos Não
Material Metal
Interruptor ligar/desligar Sim
Tipo de refrigeração Passivo
Controlo remoto incluído Sim
Definições do Equalizador Não
Conectividade de plataforma giratória Não
Função ponte Não
Telecomando W
Ligação à terra Sim
Gestão de energia
Voltagem de entrada DC 10 - 14 V
Características de potência de proteção Overheating,Short circuit
Pesos e dimensões
Largura 324 mm
Profundidade 301.6 mm
Altura 66.7 mm
Indicação
Indicadores LED
ver mais

Perguntas Frequentes

Abaixo, encontrará as perguntas mais frequentes sobre Boss Audio Systems Chaos Exxstreme CX2500D .

A sua pergunta não está na lista? Faça a sua pergunta aqui