Manual de instruções JVC RV-NB50

JVC RV-NB50
(1)
  • Número de páginas: 2
  • Tipo de arquivo: PDF
Inserting batteries
Main unit

PREPARATION

NOTE
The power will not be supplied through the batteries when the power is supplied
through the AC outlet or car battery on the unit.
The battery is consumed more quickly than usual when operating the unit
continuously or operating it in a cold place.
When the power is supplied using the batteries, the display will be blank when the
unit is turned off (at standby).
When the power is supplied using the batteries, the unit is turned on by pressing
or source buttons on the main unit.
CAUTION
To avoid battery leakage or explosion, handle batteries properly.
If you are not going to use this unit for a month or more, remove the batteries from
the battery compartment.
Dispose of batteries in the proper manner, according to federal, state, and local
regulations.
Do not mix with batteries of different types or with new and old ones.
Do not attempt to charge any batteries other than rechargeable ones.
Discard leaky batteries immediately. Battery leakage can cause skin burns or other
personal injuries.
If chemicals leak onto the unit, clean the unit completely.
Match the polarities (+ and –) of the batteries.
Remote control
If the range or effectiveness of the remote control decreases, replace the batteries.
Cautions when connecting to the car adapter
Be sure to use the car adapter (not supplied) with the same
polarity design as the one equipped with this unit to prevent
mishaps or damage.
For safety, stop the car before performing operations.
Be sure to start the engine when you use the car adapter;
otherwise, the car battery will be exhausted.
During transport, stabilize the unit in a box, etc.
To prevent malfunctions, do not leave the unit in a car for a
long time.
Connecting the power cord
Battery compartment
Discs CDs with one of the marks below on
the surface.
Files Files in audio CD format, MP3/WMA
files on a finalized CD-R or CD-RW.
MP3/WMA files in a USB device can
also be played.
Playable discs/files
Hierarchy
Level 1 Level 2 Level 3 Level 4 Level 5
Folder with its play order
MP3/WMA track with its play order
MP3/WMA folders/tracks configuration
MP3/WMA discs require a longer readout
time than regular CDs. (It depends on the
complexity of the folder/file configuration.)
Some MP3/WMA files cannot be played back
and will be skipped. This results from their
recording processes and conditions.
When making MP3/WMA discs, use ISO 9660
Level 1 for the disc format.
This unit can play back MP3/WMA files with
the extension code <.mp3> or <.wma>
(regardless of the letter case upper/lower).
It is recommended that you make each MP3
file at a sampling rate of 44.1 kHz and at a bit
rate of 128 kbps. Similarly each WMA file at a
sampling rate of 44.1 kHz and at a bit rate of
96 kbps.
Playback order of MP3/ WMA files may be
different from the one you have intended
when recording. If a folder does not contain
MP3/ WMA files, it is ignored.
This unit cannot play packet write” discs.
If a CD-RW has been recorded in a different
format, erase all data on the CD-RW
completely before recording on it.
This unit can recognize up to a total of 511
tracks and folders on a disc, and 65536 files
in up to 200 groups (maximum 500 files in a
single group) on a USB device.
For connecting/disconnecting:
USB Memory and DAPs compatible with the USB
mass storage class specifications are connectable.
Always set the volume to the minimum level when
connecting or disconnecting a USB device.
When connecting with a USB cable, use the USB 2.0
cable less than 1 m (3.28 ft) in length.
You cannot connect a computer to the USB
MEMORY terminal of the unit.
Connect one USB device to the unit at a time. Do
not use a USB hub.
When the power is supplied through the AC outlet
or car battery and USB is selected as the source, the
USB device is charged through the USB MEMORY
terminal, however some USB devices may not be
charged.
For playing back:
When connecting a USB device, refer also to its
manual.
You can play back MP3/WMA files on a USB device
(maximum data transfer rate: 2 Mbps). This unit may
not play back some files even though their formats
are listed above.
While playing back a file in a USB device, do
not disconnect the USB device. It may cause
malfunction of both this unit and the device.
This unit is compatible with USB 2.0 Full Speed.
You cannot play back a file larger than 2 Gigabytes.
When playing a file of a large transfer rate, sounds
may be dropped during playback.
This unit cannot recognize a USB mass storage class
device whose rating exceeds 5V/500 mA.
You cannot send any data to your USB device from
this unit.
Some USB devices may not be recognized or may
not work properly.
Some DAPs are not compatible with the unit.
Copyrighted tracks (WMA-DRM* tracks) cannot be
played back on the unit.
Coded or encrypted tracks in a special method
cannot be played on the unit.
Electrostatic shock at connecting a USB device may
cause abnormal playback of the device. In this case,
disconnect the USB device then reset this unit and
the USB device.
JVC bears no responsibility for any loss of data in
the USB mass storage class device while using this
unit.
* DRM (Digital Rights Management): Any of several
technical methods used to control or restrict the
use of digital media content on electronic devices
with such technologies installed.
• Compatible iPod:
iPod model
iPod nano
iPod nano (2nd Generation)
iPod nano (3rd Generation)
iPod nano (4th Generation)
iPod mini
iPod mini (2nd Generation)
iPod (4th Generation)
iPod classic
iPod photo (4th Generation)
iPod video (5th Generation)
iPod touch
iPod touch (2nd Generation)
Sound distortion may occur when playing back
audio sources with high recording levels. When
distortion occurs, it is recommended to turn
off the equalizer of iPod. For information on
operating iPod, see the iPod instruction manual.
Important for USB mass storage class device
NOTE
The power can also be supplied through the batteries (see the
instruction on the right) and the car battery (see below).
A small amount of power is always consumed even while on
standby.
CAUTION
Only use JVC power cord provided for this unit to avoid
malfunction or damage to the unit.
Remove all the batteries when using the power cord or car
battery.
Be sure to unplug the power cord from the outlet when going
out or when the unit is not in use for an extended period of
time.
Unplug the AC power cord from the unit to supply the
power through the car battery or batteries in the battery
compartment; otherwise, the unit does not work.
MaintenanceTroubleshootingDisplay
1 Timer indicators
(timer), ON
2 SLEEP indicator
3 CLOCK indicator
4 iPod indicator
5 FM mode indicators
STEREO, MONO
6 Repeat indicators
, ALL, GROUP
7 Main display
8 PRGM (program) indicator
9 RANDOM indicator
0 Frequency unit indicators
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by
the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
Important for iPod devices
Disc player
CD capacity: 1CD
Signal-to-noise ratio: 85 dB
Dynamic range: 90 dB
Tuner
FM tuning range: 87.5 MHz –
108.0 MHz
Antenna: FM telescopic
antenna
General
Speakers:
• Full range:
• Super woofer:
8 cm (3 3/16”)
cone x 2
Speaker impedance:
16 Ω
13 cm (5 1/8”)
cone x 2
Speaker impedance:
7 Ω
Output power: 40 W
Input terminal:
• USB:
Dock for iPod:
• DC IN:
Playable files:
MP3, WMA
• Compatible device:
Mass storage class
• Output power:
DC 5 V
500 mA
DC 5 V
500 mA
DC 12 V
Output terminal:
PHONES (φ3.5) x 1
As an ENERGY STAR ® Partner,
JVC has determined that
this product or product
models meet the E
NERGY STAR®
guidelines for energy efficiency.

SPECIFICATIONS

Power supply: AC 120 V , 60 Hz
DC 15 V (R20 (SUM-1)/D
(13D)-size batteries x 10)
External DC 12 V
(Car battery via the optional
car adapter)
Power
consumption: AC 120 V
, 60 Hz:
28 W (at operation)
1 W (on standby)
External DC 12 V
2 A (power on mode)
Dimensions: 666 mm (26 1/4”) x
231 mm (9 1/8”) x 240 mm
(9 1/2”) (W/H/D)
Mass:
Approx. 6.8 kg (15.0 lbs)
(without batteries stored in
the battery compartment)
Accessories
provided: Power cord x 1
Remote control x 1
Shoulder belt x 1
Buckle x 2
Stopper x 2
Design and speci cations are subject to change
without notice.
Microsoft and Windows Media are either
registered trademarks or trademarks of
Microsoft Corporation in the United States
and/or other countries.
MP3/WMA groups and tracks are not played
back as you expect.
\ Playing order is determined when the groups
and tracks were recorded. It depends on the
writing application.
The disc/USB device sound is discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied
onto the USB device.
Sounds from USB device are interrupted.
\ Noise and static electricity may stop the sound.
In this case, disconnect and connect the USB
device again after turning off the unit.
iPod Operations
iPod does not play, but CONNECT” appears on
the display.
\ The iPod battery is low or exhausted. Charge the
iPod battery.
Radio Operations
Hard to listen to broadcasts because of noise.
\ The FM antenna is not properly extended and
positioned.
\ Electrostatic discharge from your body may
cause noise. If this happens, turn off and on the
unit again.
Timer Operations
Daily Timer does not work.
\ The unit has been turned on when the on-time
comes. Timer starts working only when the unit
is turned off.
If you are having a problem with your unit, check this
list for a possible solution before calling for service.
General
Power does not come on.
\ No power is supplied. Check the power cord
connection or change the batteries.
Adjustments or settings are suddenly canceled
before you finish.
\ There is a time limit. Repeat the procedure again.
Unable to operate the unit or the unit does not
work properly.
\ The built-in microprocessor may malfunction due
to external electrical interference.
Unplug the power cord, then plug it back in.
\ Batteries are exhausted. Change the batteries.
Unable to operate the unit from the remote
control.
\ The path between the remote control and the
remote sensor on the unit is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Headphones are connected.
While the power is supplied using the batteries,
sound from the speakers is distorted or too quiet.
\ Batteries are exhausted. Change the batteries.
Disc/USB Mass Storage Class Device Operations
The disc/USB device does not play.
\ The disc is placed upside down. Place the disc with
the label side up.
\ The disc is recorded with the packet writing (UDF
file unit). It cannot be played. Check the files you
want to play back.
\ The USB device is not connected properly.
To get the best performance of the unit, keep
your discs and mechanism clean.
Handling discs
Remove the disc from its case by holding it
at the edge while pressing the center hole
lightly.
Do not touch the shiny surface of the disc, or
bend the disc.
Put the disc back in its case after use.
Be careful not to scratch the surface of the
disc when placing it back in its case.
Avoid exposure to direct sunlight,
temperature extremes, and moisture.
Cleaning discs
Wipe the disc with a soft cloth in a straight
line from center to edge.
Cleaning the unit
Stains should be wiped off with a soft cloth. If
the unit is heavily stained, wipe it with a cloth
soaked in water-diluted neutral detergent
and wrung well, then wipe clean with a dry
cloth.
Since the unit may deteriorate in quality,
become damaged or get its paint peeled off,
be careful about the following:
– DO NOT wipe it hard.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such
as insecticides to it.
– DO NOT allow any rubber or plastic to
remain in contact for a long time.
Cleaning the CD pickup lens
Keep the CD pickup lens clean, or the sound
may be degraded. Use a blower (available at a
camera store, etc.) to blow dust off the lens.

ABOUT DISC/FILE/iPod/DISPLAY

The reflection factor of CD-RW is lower than that of
other CDs, possibly causing CD-RW to take longer
time to read.
In this manual, “file and “track are interchangeably
used for MP3/WMA operations.

POWERED WOOFER CD SYSTEM

RV-NB52B/RV-NB50

Front view/Face
Side view/Côté
15 cm
(5 15/16”)
10 cm
(3 15/16”)
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by
the dimensions below.
3 Bottom:
Place on the level surface. Maintain an adequate air path
for ventilation by placing on a stand with a height of
10 cm (3 15/16”) or more.
Attention: Aération correcte
Pour prévenir tout risque de décharge électrique ou
d’incendie et éviter toute détérioration, installez l’appareil
de la manière suivante:
1 Avant:
Bien dégagé de tout objet.
2 Côtés/dessus/dessous:
Assurez-vous que rien ne bloque les espaces indiqués sur
le schéma ci-dessous.
3 Dessous:
Posez l’appareil sur une surface plane et horizontale.
Veillez à ce que sa ventilation correcte puisse se faire en
le plaçant sur un support d’au moins dix centimètres de
hauteur.
Thank you for purchasing a JVC product.
Before operation, please read the instructions carefully.
15 cm
(5 15/16”)
15 cm
(5 15/16”)
15 cm
(5 15/16”)
15 cm
(5 15/16”)
10 cm
(3 15/16”)
INSTRUCTIONS
LVT2062-001B[J/C]
0110YOMMDWBET
EN
©2009 Victor Company of Japan, Limited
For customer use:
Enter below the Model No. and Serial No. which are
located either on the rear, bottom or side of the
cabinet. Retain this information for future reference.
Model No.
Serial No.

REFERENCES

Blower
Lens
Battery compartment R20 (SUM-1)/D(13D)
(not supplied)
To cars cigarette
lighter socket
(DC12V)
Power cord
(supplied)
AC outlet
R6(SUM-3)/AA(15F)
(not supplied)
0786
34
9
521
Car adapter (not supplied)
RV-NB50[J_C].indd 1RV-NB50[J_C].indd 1 10.1.27 9:06:38 PM10.1.27 9:06:38 PM
JVC RV-NB50

Precisa de ajuda?

Número de perguntas: 0

Você tem alguma dúvida sobre o JVC RV-NB50 ou precisa de ajuda? Faça sua pergunta aqui. Forneça uma descrição clara e abrangente do problema e sua pergunta. Quanto mais detalhes você fornecer para seu problema e pergunta, mais fácil será para outros proprietários de JVC RV-NB50 responderem adequadamente à sua pergunta.

JVC RV-NB50 especificações

Não precisa de comprar altifalantes externos para obter um áudio de qualidade. Com altifalantes integrados, basta ligar ...
A comodidade na palma da sua mão, com um telecomando que torna o controlo do seu monitor mais fácil do que nunca.
Geral
Marca JVC
Modelo RV-NB50
Produto Base para altifalantes
EAN 4975769373121
Língua Inglês
Tipo de arquivo PDF
Áudio
Quantidade de equalizadores de banda 4
Conversor Áudio D/A (DAC) 1-bit
Compressão de áudio MP3,WMA
Alto-falante
Alto-falantes 4
Altifalantes incorporados Sim
Diâmetro do altifalante 80 mm
Rádio
Sintonizador digital Sim
Bandas do Rádio FM
Tipos de media
Playback CD-RW Sim
Playback CD-R Sim
Características
Playback MP3 Sim
Quantidade de estações predefinidas 30
Tipo de unidade Leitor de CD portátil
Cor do produto Black,Grey
Monitores
Visor LCD
Visor de retroiluminação Sim
Funcionalidades de gestão
Faixas Programáveis 20
Temporizador de sono Sim
Controlo remoto incluído Sim
Bateria
Tipo de bateria R20 (SUM-1) / D (13D)
Gestão de energia
Número de pilhas 10
Alimentação 230V, 50Hz; DC 15V
Outras características
Dimensões (CxLxA) 666 x 231 x 240 mm
Pesos e dimensões
Peso 6800 g
ver mais

Perguntas Frequentes

Abaixo, encontrará as perguntas mais frequentes sobre JVC RV-NB50 .

A sua pergunta não está na lista? Faça a sua pergunta aqui