Sony SNC-DH210

Manual de instruções Sony SNC-DH210

(1)
  • 4-261-054-11 (2)
    Network Camera
    Installation Manual
    Before operating the unit, please read this manual thoroughly and
    retain it for future reference.
    Owners Record
    The model and serial numbers are located on the bottom. Record these
    numbers in the spaces provided below.
    Refer to these numbers whenever you call upon your Sony dealer
    regarding this product.
    Model No. Serial No.
    WARNING
    To reduce a risk of fire or electric shock, do not
    expose this product to rain or moisture.
    To avoid electrical shock, do not open the cabinet.
    Refer servicing to qualified personnel only.
    WARNING
    This installation should be made by a qualified service person and
    should conform to all local codes.
    WARNING
    A readily accessible disconnect device shall be incorporated in the
    building installation wiring.
    WARNING (for Installers only)
    Instructions for installing the equipment on the ceiling or the wall:
    After the installation, ensure the connection is capable of supporting at
    least a force of 50 Newtons (N) downwards.
    CAUTION
    The rating label is located on the bottom.
    CAUTION for LAN port
    For safety reason, do not connect the LAN port to any network devices
    that might have excessive voltage.
    The LAN port of this unit is to be connected only to the devices whose
    power feeding meets the requirements for SELV (Safety Extra Low
    Voltage) and complies with Limited Power Source according to IEC
    60950-1.
    Use IEEE802.3af standard compliant devices.
    For customers in the U.S.A.
    This device complies with Part 15 of the FCC Rules. Operation
    is subject to the following two conditions: (1) This device may
    not cause harmful interference, and (2) this device must accept
    any interference received, including interference that may cause
    undesired operation.
    NOTE: This equipment has been tested and found to comply with the
    limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
    These limits are designed to provide reasonable protection against
    harmful interference when the equipment is operated in a commercial
    environment. This equipment generates, uses, and can radiate radio
    frequency energy and, if not installed and used in accordance with
    the instruction manual, may cause harmful interference to radio
    communications. Operation of this equipment in a residential area
    is likely to cause harmful interference in which case the user will be
    required to correct the interference at his own expense.
    You are cautioned that any changes or modifications not expressly
    approved in this manual could void your authority to operate this
    equipment.
    All interface cables used to connect peripherals must be shielded in
    order to comply with the limits for a digital device pursuant to Subpart
    B or Part 15 of FCC Rules.
    For customers in Canada
    This Class A digital apparatus complies with Canadian ICES-003.
    Cet appareil numérique de la classe A est conforme à la norme
    NMB-003 du Canada.
    For the customers in Europe
    The manufacturer of this product is Sony Corporation, 1-7-1 Konan,
    Minato-ku, Tokyo, Japan.
    The Authorized Representative for EMC and product safety is Sony
    Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
    For any service or guarantee matters please refer to the addresses given
    in separate service or guarantee documents.
    For the customers in Europe, Australia and New Zealand
    WARNING
    This is a Class A product. In a domestic environment, this product may
    cause radio interference in which case the user may be required to take
    adequate measures.
    In the case that interference should occur, consult your nearest
    authorized Sony service facility.
    This apparatus shall not be used in the residential area.
    ATTENTION
    The electromagnetic fields at specific frequencies may influence the
    picture of the unit.
    Notes on Use
    Before Use
    If you find condensation before use, leave the camera out for long
    enough and do not turn on the power until the condensation
    disappear.
    Remove static electricity before installation and operation.
    Data and security
    You should keep in mind that the images or audio you are
    monitoring may be protected by privacy and other legal rights, and
    the responsibility for making sure you are complying with applicable
    laws is yours alone.
    Access to the images and audio is protected only by a user name
    and the password you set up. No further authentication is provided
    nor should you presume that any other protective filtering is done
    by the service. Since the service is Internet-based, there is a risk that
    the image or audio you are monitoring can be viewed or used by a
    third-party via the network.
    SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO
    LIABILITY TO YOU OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR
    DISCONTINUATIONS OR EVEN SERVICE CANCELLATION. THE SERVICE
    IS PROVIDED AS-IS, AND SONY DISCLAIMS AND EXCLUDES ALL
    WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE SERVICE
    INCLUDING, BUT NOT LIMITED TO, ANY OR ALL IMPLIED WARRANTIES
    OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
    THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.
    Always make a test recording, and verify that it was recorded
    successfully. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY
    KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR
    REIMBURSEMENT ON ACCOUNT OF FAILURE OF THIS UNIT OR ITS
    RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR ANY OTHER
    MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.
    Always verify that the unit is operating properly before use. SONY
    WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING,
    BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON
    ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE
    TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD
    OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER
    REASON WHATSOEVER.
    If you lose data by using this unit, SONY accepts no responsibility for
    restoration of the data.
    Personal information
    The images taken by the system using this device can identify
    individuals and thus they fall under “personal information stipulated
    in the Act on the Protection of Personal Information. Please handle
    the video data appropriately according to law.
    Information recorded using this product may also be “personal
    information. Upon disposal, transfer, repair, or any other occasion
    where this product or storage media is passed on to a third party,
    practice due care in its handling.
    Operating or storage location
    Do not shoot an extremely bright object (an illumination, the sun, etc.).
    Also, avoid operating or storing the camera in the following locations,
    as these can be a cause of a malfunction.
    Extremely hot or cold places (Operating temperature: 0°C to 50°C
    [32°F to 122°F])
    Exposed to direct sunlight for a long time, or close to heating
    equipment (e.g., near heaters)
    Close to sources of strong magnetism
    Close to sources of powerful electromagnetic radiation, such as
    radios or TV transmitters
    Locations subject to strong vibration or shock
    Humid or dusty locations
    Locations exposed to rain
    Locations under the influence of fluorescent light or reflection of a
    window
    Under an unsteady light (the image will flicker.)
    Ventilation
    To prevent heat buildup, do not block air circulation around the camera.
    Power supply
    The power of this model is supplied by network cable.
    Use the network cable UTP, category-5.
    Damage to the network cable may result in fire or electric shock.
    Transportation
    Always turn off the power when carrying.
    When transporting the camera, repack it as originally packed at the
    factory or in materials of equal quality.
    Cleaning
    Use a blower to remove dust from the lens.
    Use a soft, dry cloth to clean the external surfaces of the camera.
    Stubborn stains can be removed using a soft cloth dampened with a
    small quantity of detergent solution, then wipe dry.
    Do not use volatile solvents such as alcohol, benzene or thinners as
    they may damage the surface finishes.
    Note on laser beams
    Laser beams may damage image sensors. You are cautioned that
    the surface of image sensors should not be exposed to laser beam
    radiation in an environment where a laser beam device is used.
    Phenomena Specific to Image Sensors
    The following phenomena that may occur in images are specific to
    image sensors. They do not indicate a malfunction.
    White flecks
    Although the image sensors are produced with high-precision
    technologies, fine white flecks may be generated on the screen in rare
    cases, caused by cosmic rays, etc.
    This is related to the principle of image sensors and is not a
    malfunction.
    The white flecks especially tend to be seen in the following cases:
    when operating at a high environmental temperature
    when you have raised the gain (sensitivity)
    when using the slow shutter
    Aliasing
    When fine patterns, stripes, or lines are shot, they may appear jagged
    or flicker.
    About the Supplied Manuals
    Installation Manual (this document)
    This Installation Manual describes the names and functions of parts
    and controls of the Network Camera, gives connection examples and
    explains how to set up the camera. Be sure to read the Installation
    Manual before operating.
    The pictures of SNC-DH210T are mainly used in explanatory examples.
    User’s Guide (stored in the CD-ROM)
    The User’s Guide describes how to set up the camera and how to
    control the camera via a Web browser.
    After installing and connecting the camera correctly, operate referring
    to this User’s Guide.
    Using the CD-ROM Manuals
    The supplied CD-ROM disc includes the Users Guides for this unit in
    PDF format.
    Preparations
    The Adobe Reader Version 6.0 or higher must be installed on your
    computer in order to use the guides stored in the CD-ROM disc.
    Note
    If Adobe Reader is not installed, it may be downloaded from the following URL:
    http://www.adobe.com/
    Reading the manual in the CD-ROM
    1 Insert the CD-ROM in your CD-ROM drive.
    A cover page appears automatically in your Web browser.
    If it does not appear automatically in the Web browser, double-click
    on the index.htm file on the CD-ROM.
    2 Select and click on the manual that you want to read.
    This opens the PDF file of the manual.
    Clicking an item in the Table of Contents allows you jump to the
    relevant page.
    Notes
    The files may not be displayed properly, depending on the version of Adobe
    Reader. In this case, install the latest version, which you can download from the
    URL mentioned in “Preparations” above.
    If you have lost or damaged the CD-ROM, you can purchase replacement.
    Contact your Sony service representative.
    Adobe and Acrobat Reader are trademarks of Adobe Systems
    Incorporated in the United States and/or other countries.
    Location and Function of Part
    Appearance
    Dome casing
    PT (Pan/Tilt) casing
    Care should be taken while turning the PT casing, as it may separate
    if pulled it too hard.
    Should this occur, see“When the PT casing separateson the reverse
    side, and install the casing correctly.
    lens casing
    Normal cover (SNC-DH210 only)
    Clear cover (SNC-DH210T only)
    Hook
    Press the hook inward and meanwhile turn the dome casing, then
    remove the dome casing from the camera unit.
    Knockout type flange
    When threading the cables through the side of the camera, use
    pliers to break off the knockout flange (with pliers, etc.).
    TOP
    The figure shows the camera without the dome casing and the cover.
    Camera unit
    Lens
    A fixed-focus lens is mounted.
    Reset switch
    Turn on the power of the camera, holding down the switch for a
    further 30 seconds to reset the camera to the factory default
    settings.
    MONITOR out connector [AV minijack]
    Output the composite video signal from the camera.
    Monitor out is used when you adjust the view angle.
    Before use, see the procedure from“Setting the view angle of the
    monitor out”.
    Note
    Before use, it is neseccery to connect to the PC and change the
    system setting.
    POWER indicator (Green)
    When the power is supplied to the camera, the camera starts
    checking the system. If the system is normal, this indicator lights up.
    NETWORK indicator (Green/Orange)
    The indicator lights up or flashes when the camera is connected to
    the network. The indicator is off when the camera is not connected
    to the network. When 100BASE-TX is connected, the indicator turns
    green. When 10BASE-T is connected, the indicator turns orange.
    NTSC/PAL switch
    Switching the video output.
    Bottom
    Fall-prevention rope mounting hole
    When installing the camera on a ceiling or a wall. Be sure to secure a
    fall-prevention rope (not supplied) to this hole for safety.
    LAN connector (PoE) [RJ-45]
    Use the network cable (UTP, category-5) for network
    communications and PoE* power supply.
    LAN cable [RJ-45] is connected when the unit comes from the
    factory.
    See “Connect to the Network” for connection.
    (* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard
    compliant devices.)
    Sensor Input
    Connect the supplied sensor input cable. (The cable is not
    connected when the unit comes from the factory.)
    Sensor input
    cable color
    Signal
    Red Sensor input +
    White Sensor input – (GND)
    For details on function and required settings, refer to the User’s
    Guide stored in the supplied CD-ROM.
    For the wiring, see Wiring diagram for sensor input.
    Camera installation hole (2 positions)
    Make sure to tighten the screws securely when installing the
    camera.
    Model name label
    This label shows device information, such as the model name and
    serial number.
    MAC Address label
    Indicates the MAC address of this camera.
    (continued on the reverse side)
    SNC-DH210/DH210T
    2010 Sony Corporation Printed in China
    SNC-DH210 SNC-DH210T
Sony SNC-DH210

Precisa de ajuda?

Número de perguntas: 0

Você tem alguma dúvida sobre o Sony SNC-DH210 ou precisa de ajuda? Faça sua pergunta aqui. Forneça uma descrição clara e abrangente do problema e sua pergunta. Quanto mais detalhes você fornecer para seu problema e pergunta, mais fácil será para outros proprietários de Sony SNC-DH210 responderem adequadamente à sua pergunta.

Veja o manual do Sony SNC-DH210 aqui, de graça. Este manual está na categoria Câmeras de vigilância e foi avaliado por 1 pessoas com uma média de 6.3. Este manual está disponível nos seguintes idiomas: Inglês. Você tem alguma dúvida sobre o Sony SNC-DH210 ou precisa de ajuda? Faça a sua pergunta aqui

Sony SNC-DH210 especificações

Geral
Marca Sony
Modelo SNC-DH210
Produto Câmara de vigilância
EAN 27242812369
Língua Inglês
Tipo de arquivo PDF
Vídeo
Formatos de vídeo H.264
Resolução Máxima 2048 x 1536
Taxa de fotogramas 15
Formato de sistema de sinal analógico NTSC, PAL
Câmera
Ângulo de visão (horizontal) 88
Velocidade do obturador 1 - 1/10000
Inclinação 0 - 60
Iluminação mínima 2
Equilíbrio dos brancos Auto, Manual
Sensor de imagem
Tipo de sensor de imagem CMOS
Tamanho do sensor ótico 1/2.8 2011-05-04 11:27:54 2012-06-08 13:40:02 3157 16 13
Rede
Tecnologia de cablagem 10/100Base-T(X)
Protocolos de rede suportados IPv4, IPv6, TCP, UDP, ARP, ICMP, IGMP, HTTP, HTTPS, FTP (client), SMTP, DHCP, DNS, NTP, RTP/RTCP, RTSP, SNMP (MIB-2)
Outras características
Velocidade real de transferência 100
Interface de rede Fast Ethernet
Dimensões do produto (CxLxA) 106 x 106 x 50.5
Sistemas operativos compatíveis WindowsXP, WindowsVista, Windows7
Gestão de energia
Power over Ethernet (PoE)
Consumo de energia (típico) 2.4
Tipo de fonte de alimentação PoE
Conectividade
Quantidade de portas Ethernet LAN (RJ-45) 1
Modo noturno
Versão noturna
Pesos e dimensões
Peso do produto 160
null
Requisitos do sistema
Velocidade de processador mínima Intel Core2 Duo 2 GHz
Memória RAM mínima 1024
Condições ambientais
Temperatura de funcionamento 0 - 50
Limite de temperaturas (armazenamento) -20 - 60
Desempenho
Certificação UL2044, FCC 15B A, IC A, IEC60950-1, EN55022(A)+EN55024+EN50130-4, VCCI A,
C-Tick A
Segurança
Deteção de movimentos vídeo

Perguntas Frequentes

Abaixo, encontrará as perguntas mais frequentes sobre Sony SNC-DH210 .

A sua pergunta não está na lista? Faça a sua pergunta aqui

ManualPDF.pt

Procurando um manual? ManualPDF.pt garante que encontrará o manual que está a procurar rapidamente. O nosso banco de dados contém mais de 1 milhão de manuais em PDF de mais de 10.000 marcas. Todos os dias adicionamos os manuais mais recentes para que sempre encontre o produto que procura. É muito simples: basta digitar o nome da marca e o tipo de produto na barra de pesquisa e pode visualizar instantaneamente o manual de sua escolha online gratuitamente.

ManualPDF.pt

© Copyright 2020 ManualPDF.pt. Todos os direitos reservados.

Utilizamos cookies para assegurar que lhe fornecemos a melhor experiência na nossa página web. Se continuar a utilizar esta página pressupomos que está feliz por a utilizar.

Ler mais